2.2 เข้าใจเกี่ยวกับ IP Address
ใน TCP/IP จะมีกลไกในการแม็บกับค่า MAC Address ที่ติดต่อเรียกขั้นตอนนี้ว่า Address Resolution Protocol (ARP) ซึ่งจะมีการสร้างตาราง ARP ที่แม็บ Logical Address (IP Address) กับ Mac address ขั้นตอนในการติดต่อ1. ถ้าตำแหน่งที่ติดต่ออยู่ใน Network segment เดียวกันระบบสามารถที่จะส่งจาก Source และ Destination ได้โดยตรง2. แต่ถ้า Destination อยู่ต่างที่กันระบบจะทำงานดังนี้a. ข้อมูลส่งไปที่ gateway โดยใช้ ARP ตาราง ARP Cached จะบันทึก MAC address กับ IP Address ของ Routerb. ในข้อมูลจะส่งผ่านโดยดูใช้ชั้นที่สูงขึ้นคือ Internet แสดงส่งข้อมูลโดยพิจารณาจาก Routing Tablec. เมื่อผ่าน Router ไปถึงเป้าหมายก็จะส่งในขา Router นั้นไปที่เป้าหมายที่ต้องการในการส่งข้อมูลนี้จะต้อง- ระบุเครื่องบนเครือข่าย- ต้องมีการกำหนด Gateway ที่ Router- อุปกรณ์ที่ใช้ต่างกันจะต้องมี Router ในการส่งข้าม เช่น Token Ring กับ Ethernet หรือ LAN กับ WAN- มีการแปลง Logical IP Address ของ Destination network ไปเป็น Physical address ของเครื่องที่ติดต่อการส่งข้อมูลระบบสามารถใช้ IP กับ ARP ในชั้น Internet และสามารถที่ใช้ ICMP protocol ในการตรวจสอบปัญหา และแก้ปัญหาInternet ProtocolIP Protocol เป็นอิสระกับฮาร์ดแวร์ที่มีความสลับซับซ้อน สามารถที่ Route ข้ามเครือข่ายหมายเลขจะต้องมีหมายเลขเดียวในเครือข่ายเลขที่ใช้คือเลขฐาน 10 สี่ตัว มีการแยก Network ID กับ Host ID ฟิลด์ IP Header (มาตรฐาน RFC 791)- Version ระบุว่าเป็นเวอร์ชั่น 4 หรือ 6 เช่น 0100 เป็นเวอร์ชั่น 4- Internet Header Length (IHL) ใช้ 4 บิตในการบอกความยาวของ IP header - Type of Service โดยทั่วไปเป็น Normal- Total Length
- Identification ใช้ร่วมกับ Flags และ Fragment Offset ถ้ามีการแตกข้อมูลหมายเลข ID ต้องตรงกัน- Flags เป็นการระบุว่าข้อมูลนี้มีอีกหรือไม่ - Fragment Offset เป็นการระบุตำแหน่งใช้ในการรวมข้อมูล- Time to Live เป็นค่าที่ใช้ลดปัญหาแพ็ตเกจข้อมูลขยะ- Protocol ถ้าเป็น ICMP หมายเลขคือ 1, TCP คือ 6, UDP คือ 17- Header Checksum ใช้ตรวจสอบความถูกต้องข้อมูล- Source IP Address
- Destination IP Address
- IP Options
- Padding
- IP Data payload
IP Addressingมีการแบ่งดังนี้Address Class หมายเลขของออกเตตแรก บิตที่จอง (จากบิตแรก) Subnet Mask จำนวน Networks จำนวน Hosts
A 0-126 0 255.0.0.0 126 256*256*256 - 2
B 128-191 10 255.255.0.0 256*64 256*256-2
C 192-223 110 255.255.255.0 32*256*256 254
D 224-239 1110 255.255.255.240 จองสำหรับ Multicast
E 240-248 11110 255.255.255.248 จองไว้ไม่ได้ใช้
หมายเหตุ *127 ไม่ใช้เพราะเป็น Local Loopbackหมายเลข IP แบ่งเป็น Public IP Address กับ Private IP Addressโดยทั่วไปเป็น IP สาธารณะ องค์กรที่กำหนดหมายเลขหรือให้กลุ่มหมายเลขที่ไม่ซ้ำกัน IANA (Internet Assigned Numbers Authority)แบ่งออกเป็น 4 ย่านคือ- APNIC
- ARIN
- LACNIC
- RIPE
และ IP Address ที่อยู่ช่วงนี้10.0.0.0-10.255.255.255, 172.16.0.0-172.31.255.255, 192.168.0.0- 192.168.255.255, 169.254.0.0- 169.254.255.255
เป็น IP ส่วนตัวคลาส D และ Eในการสื่อสาร TCP/IP เป็นการติดต่อจาก Host-to-Host ถ้าเป็นคลาส D จะเป็นการติดต่อแบบ Multicast ดูตารางด้านบนควบคู่กัน หมายเลข IP พิเศษในบิต 255 จะเป็นการบรอดคลาสเช่น Network ID 129.152 มีการบรอดคลาสโดยใช้ 129.152.255.255ถ้าเป็น 255.255.255.255 เป็นการบรอดคลาสทั้ง Network และ 127, 10, 172, 192.168, 169.254 ดูด้านบนเป็น Private IP127.x.x.x เป็น Local Loopback255.255.255.255 เป็นบรอดคลาส10.x.x.x เป็น Private Class A172.16.x.x-172.31.x.x เป็น Private Class B192.168.x.x เป็น Private Class C
169.254.x.x ใช้เป็น AutoPrivate IP Address 0.0.0.0 บอกถึง Network ทั้งหมด
วิธีตรวจสอบ IP Addressเราสามารถกำหนด IP Address ได้แบบต่างๆดังนี้- กำหนดด้วยมือ- กำหนดด้วย DhCP- ใช้แบบ Automatic Private IP Addressing - การกำหนดค่า Alternate configuration เอง คือไม่มี DHCP Server แต่ผู้ดูแลกำหนดเองให้เป็น IP Address ที่ต้องการ
ความเข้าใจเกี่ยวกับ IP addressผู้เรียนพบว่าหมายเลข IP Address แบ่งเป็น 4 ชุด ชุดละ 8 บิต ถูกแปลงจากเลขฐานสองเป็นเลขฐานสิบดังนั้นผู้กำหนด IP Address ต้องมีความเข้าใจในการแปลงเลขฐานสองเป็นฐานสิบ และจากฐานสิบไปเป็นฐานสอง โดยอาจจะใช้เครื่องคิดเลขเข้้าช่วยได้ค่าหมายเลขที่กำหนดแบ่งเป็นสองชุดหลักๆคือ Network ID และ Host ID โดยค่า Subnet mask เป็นตัวแบ่งเครือข่าย เช่น 192.168.2.11 Subnet mask เป็น 255.255.255.0 Network ID คือ 192.168.2.0 ์Host ID คือ 11บางครั้งจะเขียนเป็นจำนวนบิตแทนดังนี้ 192.168.2.11/24 มีความหมายเดียวกันโดยทั่วไปถ้าเป็น Class A, B, C จะมีค่า Subnet Mask ดีฟอลท์อยู่แล้วจากตารางด้านบน แต่ถ้ากำหนดแตกต่างก็มีสิทธิเป็นไปได้เรียกว่าการแบ่ง Subnetting หรือ Supernettingเมื่อพบว่าเครื่องที่ติดต่ออยู่ต่างเครือข่ายกันจะต้องมีการกำหนด default gateway เพื่อเป็นทางออกในการส่งต่อไปยังเครื่องที่อยู่ภายนอก
วันอังคารที่ 20 กรกฎาคม พ.ศ. 2553
เข้าใจเกี่ยวกับ TCP/IP
หน้าแรก | สารบัญ | ภาพรวม | แสดงไอค่อน
Network Infrastructure (70-291)
ขอข้อมูลเพิ่มติดต่อ information@itcompanion.co.th
หน้าแรก
1. เข้าใจเกี่ยวกับเครือข่าย Wi...
2. เข้าใจเกี่ยวกับ TCP/IP
2.1 เข้าใจเกี่ยวกับ TCP/IP
2.2 เข้าใจเกี่ยวกับ IP Address
2.3 การแบ่ง Subnetting และ Sup...
2.4 การติดตั้ง และกำหนดค่าติดต...
2.5 ปฏิบัติการกำหนดค่าติดตั้ง ...
3. เฝ้าดู และการแก้ปัญหาการเชื...
4. กำหนดค่า DNS Server และ Cli...
5. การวางระบบโครงสร้างพื้นฐาน ...
6. เฝ้าดู และการแก้ปัญหา DNS
7. กำหนดค่า DHCP Servers และ C...
8. เฝ้าดู และการแก้ปัญหา DHCP
9. การหาเส้นทางใน Windows Serv...
10. การกำหนดค่า และการจัดการ R...
11. การจัดการ Network Security
12. การบำรุงรักษาโครงสร้างพื้น...
หน้าแรก > 2. เข้าใจเกี่ยวกับ TCP/IP > 2.1 เข้าใจเกี่ยวกับ TCP/IP ก่อนหน้า ต่อไป
2.1 เข้าใจเกี่ยวกับ TCP/IP
TCP/Ip เป็นโปรโตคอลพื้นฐานที่ใช้งานบน Windows networks และ Internet โดยแบ่งการทำงานออกเป็น 4 ลำดับชั้นคือApplication
Transport
Internet
Network Interface
ส่วนประกอบที่ทำงานใน TCP/IP คือชั้น Transport และ Internetการติดต่อ TCP/IP ในการวิ่งข้ามเครือข่ายระบบจะใช้การสร้างแพ็คเกจใหม่เมื่อมีการติดต่อ (ไม่ต้องสนใจอุปกรณ์ สนใจแต่ข้อมูล) การทำงานของ TCP/IP เป็นลำดับชั้นดูในตารางด้านล่างแบ่งการทำงานออกเป็นลำดับชั้น 4 ชั้นดังนี้Application รองรับการทำงาน การแก้ปัญหา เช่น File Transfer, Remote Control, Internet activities
Transport เป็นผู้รับผิดชอบ Flow Control, Error Control, Acknowledgement
Internet รองรับหมายเลขที่กำหนดเอง (Logical Address) เป้าหมายคือการติดต่อให้ถึงกับเครื่องที่ต้องการ ซึ่งจะมี Logical Address ที่จะแม็บกับ Physical Address
Network Access รองรับการต่อเชื่อมกับอุปกรณ์กายภาพ มีการกำหนดรูปแบบของข้อมูล และ Physical Address, รองรับ Error control ที่ส่งในเครือข่าย Physical
ในการติดต่อระดับ Application เมื่อมีการส่งข้อมูลลงมาจะมีการปะ Header ในแต่ละลำดับชั้น ผู้รับเมื่อได้รับข้อมูลก็จะทำการตรวจ Header และนำ Header ออกในแต่ละลำดับชั้นเพื่อดึงข้อมูลที่ติดต่อจริงๆTCP/IP กับ OSI Modelมาตรฐานการสื่อสารแบ่งเป็น 7 ชั้นซึ่งเรียกว่า Open System Interconnection (OSI) Model ในมาตรฐาน TCP/IP ก็ถูกออกแบบมาให้สอดคล้องกับ OSI ซึ่งมีรูปเปรียบเทียบดังนี้TCP/IP Stack OSI Model
Application Application
Presentation
Session
Transport Transport
Internet Network
Network Access Data Link
Physical
- Physical เป็นการส่งข้อมูลในระดับสัญญาณไฟฟ้า และอุปกรณ์ที่ใช้- Data Link เป็นชั้นเชื่อมต่อข้อมูลกับการส่งข้อมูลทางไฟฟ้า ซึ่งจะมีการกำหนด Logical Link หรือที่เราใช้คำว่า Frame เช่นแปลงเลขฐาน 2 ให้เป็น Start frame หรือ End of frame- Network รองรับ Logical Addressing และการ Routing- Transport ควบคุมข้อมูลทั้ง Error, และ Flow - Session บอกถึงเทคนิคการติดต่อ เช่น Simplex, Half Duplex, Full Duplex- Presentation แปลงข้อมูลในมาตรฐาน (ข้อมูลดิบ) เช่น การเข้ารหัส, ASCII, Unicode, Data Compression- Application คือแอพพลิเคชั่นที่เรียกใช้ที่สามารถอำนวยความสะดวกในการใช้งานมีทั้งที่เป็น Command line, GUIแพ็คเกจข้อมูลในการส่ง Package ข้อมูลในชั้นบนจะถูกมองเป็นดาต้าในชั้นถัดไป เช่น ดังรูปด้านล่างสีเทาคือ Header ที่ปะในแต่ละชั้น Application
Transport
Internet
Network Access
-> 1010111100010…
ขั้นตอน◦แพ็คเกจข้อมูลที่สร้างจาก Application เรียกว่า Messages ◦มาในชั้น Transport จะถูกเข้าข้อมูลไว้เป็น Segment ซึ่งเป็นข้อมูลขนาดเล็กเรียกว่า User Datagram Protocol (UDP) ◦ข้อมูลในชั้น Internet จะบรรจุข้อมูลของ Datagram ในชั้น Transport และมีการส่งข้อมูลเรียกว่า Datagram หรือ Package ◦ข้อมูลที่ชั้น Network Access จะบรรจุ และทำการแปลงข้อมูลข้อมูลเรียกว่าเฟรม (Frame) ถ้าใช้เครือข่าย ATM ข้อมูลจะเรียกว่า (Cell)
การต่อเชื่อมเครือข่าย TCP/IP ดูอย่างเร็วๆสมมติว่าคุณใช้ FTP ในโอนถ่ายไฟล์ระบบจะตรวจสอบว่าเป็น TCP หรือ UDP ในที่นี้คือ TCP -> ส่งไปที่ Internet จะทำการปะตำแหน่งที่ติดต่อระหว่างต้นทางกับปลายทางที่เรียกว่า Logical Address -> ระบบติดต่อผ่านอุปกรณ์ต่างๆจะใช้การประกบกันของ Logical Address กับ Physical Address (ARP, RARP)ซึ่งจะขึ้นอยู่กับประเภทของอุปกรณ์ เราจะใส่เฟรมไม่เหมือนกัน
Network Infrastructure (70-291)
ขอข้อมูลเพิ่มติดต่อ information@itcompanion.co.th
หน้าแรก
1. เข้าใจเกี่ยวกับเครือข่าย Wi...
2. เข้าใจเกี่ยวกับ TCP/IP
2.1 เข้าใจเกี่ยวกับ TCP/IP
2.2 เข้าใจเกี่ยวกับ IP Address
2.3 การแบ่ง Subnetting และ Sup...
2.4 การติดตั้ง และกำหนดค่าติดต...
2.5 ปฏิบัติการกำหนดค่าติดตั้ง ...
3. เฝ้าดู และการแก้ปัญหาการเชื...
4. กำหนดค่า DNS Server และ Cli...
5. การวางระบบโครงสร้างพื้นฐาน ...
6. เฝ้าดู และการแก้ปัญหา DNS
7. กำหนดค่า DHCP Servers และ C...
8. เฝ้าดู และการแก้ปัญหา DHCP
9. การหาเส้นทางใน Windows Serv...
10. การกำหนดค่า และการจัดการ R...
11. การจัดการ Network Security
12. การบำรุงรักษาโครงสร้างพื้น...
หน้าแรก > 2. เข้าใจเกี่ยวกับ TCP/IP > 2.1 เข้าใจเกี่ยวกับ TCP/IP ก่อนหน้า ต่อไป
2.1 เข้าใจเกี่ยวกับ TCP/IP
TCP/Ip เป็นโปรโตคอลพื้นฐานที่ใช้งานบน Windows networks และ Internet โดยแบ่งการทำงานออกเป็น 4 ลำดับชั้นคือApplication
Transport
Internet
Network Interface
ส่วนประกอบที่ทำงานใน TCP/IP คือชั้น Transport และ Internetการติดต่อ TCP/IP ในการวิ่งข้ามเครือข่ายระบบจะใช้การสร้างแพ็คเกจใหม่เมื่อมีการติดต่อ (ไม่ต้องสนใจอุปกรณ์ สนใจแต่ข้อมูล) การทำงานของ TCP/IP เป็นลำดับชั้นดูในตารางด้านล่างแบ่งการทำงานออกเป็นลำดับชั้น 4 ชั้นดังนี้Application รองรับการทำงาน การแก้ปัญหา เช่น File Transfer, Remote Control, Internet activities
Transport เป็นผู้รับผิดชอบ Flow Control, Error Control, Acknowledgement
Internet รองรับหมายเลขที่กำหนดเอง (Logical Address) เป้าหมายคือการติดต่อให้ถึงกับเครื่องที่ต้องการ ซึ่งจะมี Logical Address ที่จะแม็บกับ Physical Address
Network Access รองรับการต่อเชื่อมกับอุปกรณ์กายภาพ มีการกำหนดรูปแบบของข้อมูล และ Physical Address, รองรับ Error control ที่ส่งในเครือข่าย Physical
ในการติดต่อระดับ Application เมื่อมีการส่งข้อมูลลงมาจะมีการปะ Header ในแต่ละลำดับชั้น ผู้รับเมื่อได้รับข้อมูลก็จะทำการตรวจ Header และนำ Header ออกในแต่ละลำดับชั้นเพื่อดึงข้อมูลที่ติดต่อจริงๆTCP/IP กับ OSI Modelมาตรฐานการสื่อสารแบ่งเป็น 7 ชั้นซึ่งเรียกว่า Open System Interconnection (OSI) Model ในมาตรฐาน TCP/IP ก็ถูกออกแบบมาให้สอดคล้องกับ OSI ซึ่งมีรูปเปรียบเทียบดังนี้TCP/IP Stack OSI Model
Application Application
Presentation
Session
Transport Transport
Internet Network
Network Access Data Link
Physical
- Physical เป็นการส่งข้อมูลในระดับสัญญาณไฟฟ้า และอุปกรณ์ที่ใช้- Data Link เป็นชั้นเชื่อมต่อข้อมูลกับการส่งข้อมูลทางไฟฟ้า ซึ่งจะมีการกำหนด Logical Link หรือที่เราใช้คำว่า Frame เช่นแปลงเลขฐาน 2 ให้เป็น Start frame หรือ End of frame- Network รองรับ Logical Addressing และการ Routing- Transport ควบคุมข้อมูลทั้ง Error, และ Flow - Session บอกถึงเทคนิคการติดต่อ เช่น Simplex, Half Duplex, Full Duplex- Presentation แปลงข้อมูลในมาตรฐาน (ข้อมูลดิบ) เช่น การเข้ารหัส, ASCII, Unicode, Data Compression- Application คือแอพพลิเคชั่นที่เรียกใช้ที่สามารถอำนวยความสะดวกในการใช้งานมีทั้งที่เป็น Command line, GUIแพ็คเกจข้อมูลในการส่ง Package ข้อมูลในชั้นบนจะถูกมองเป็นดาต้าในชั้นถัดไป เช่น ดังรูปด้านล่างสีเทาคือ Header ที่ปะในแต่ละชั้น Application
Transport
Internet
Network Access
-> 1010111100010…
ขั้นตอน◦แพ็คเกจข้อมูลที่สร้างจาก Application เรียกว่า Messages ◦มาในชั้น Transport จะถูกเข้าข้อมูลไว้เป็น Segment ซึ่งเป็นข้อมูลขนาดเล็กเรียกว่า User Datagram Protocol (UDP) ◦ข้อมูลในชั้น Internet จะบรรจุข้อมูลของ Datagram ในชั้น Transport และมีการส่งข้อมูลเรียกว่า Datagram หรือ Package ◦ข้อมูลที่ชั้น Network Access จะบรรจุ และทำการแปลงข้อมูลข้อมูลเรียกว่าเฟรม (Frame) ถ้าใช้เครือข่าย ATM ข้อมูลจะเรียกว่า (Cell)
การต่อเชื่อมเครือข่าย TCP/IP ดูอย่างเร็วๆสมมติว่าคุณใช้ FTP ในโอนถ่ายไฟล์ระบบจะตรวจสอบว่าเป็น TCP หรือ UDP ในที่นี้คือ TCP -> ส่งไปที่ Internet จะทำการปะตำแหน่งที่ติดต่อระหว่างต้นทางกับปลายทางที่เรียกว่า Logical Address -> ระบบติดต่อผ่านอุปกรณ์ต่างๆจะใช้การประกบกันของ Logical Address กับ Physical Address (ARP, RARP)ซึ่งจะขึ้นอยู่กับประเภทของอุปกรณ์ เราจะใส่เฟรมไม่เหมือนกัน
โครงสร้างเครือข่ายพื้นฐานเพิ่มเติม
1.3 โครงสร้างเครือข่ายพื้นฐานเพิ่มเติม
เราสามารถที่ติดตั้งบริการ โปรโตคอล หรือลูกข่ายต่างๆใน Windows server 2003 เพิ่มได้ ซึ่งบางอย่างเป็นส่วนประกอบ บางอย่างเป็น Roles หรือบทบาทในเครื่องแม่ข่าย เช่น DNS, WINS, DHCP เป็นต้นการเพิ่มส่วนประกอบโดยดีฟอลท์ Windows Server 2003 จะมีหมายเลข IP และเป็น Workgroup มี NetBIOS ทำงานบน TCP/IP โดยบรอดคลาสให้เครื่องต่างๆติดต่อเข้ามาทั้งใช้แชร์ ความปลอดภัย การขอดูเครื่อง และการพิมพ์ ส่วนประกอบที่มีคือ Client for Microsoft Network กับ File and Printer Sharing for Microsoft Netw, TCP/IPเราสามารถที่ผูกกับ Clients, Services, Protocols อื่นๆได้โดยการคลิกปุ่ม Installการติดตั้ง Client Service for Netware ต้องมีการติดตั้ง NWLink (IPX) Protocol ก่อนเมื่อติดตั้งต้องมีการกำหนด Frame Types และ Network node ถ้าเลือก Autodetect จะได้เพียงหนึ่งเพิ่ม ถ้าต้องการมากกว่าหนึ่งให้กำหนด้วย Manual
ส่วนประกอบเครือข่ายอื่นๆเราสามารถติดตั้งได้โดยปที่ Add or Remove Programs ใน Control Panel > Add/Remove Windows Components > เลือกส่วนประกอบที่ต้องการซึ่งมี Management and Monitoring Tools, Network Services, Orther Network File and Print Services, และ Certificate Servicesภายในแต่ละส่วนประกอบหลักจะประกอบด้วยManagement and Monitoring Tools มี- Connection manager administration kit
- Connection Point Services
- Network Monitor tools
- Simple Network Management Protocol
- WMI SNMP Provider
ส่วนประกอบ Networking Services มี- Domain Name System (DNS)
- Dynamic Host Configuration Protocol (DHCP)
- Internet authentication services
- RPC over HTTP Proxy
- Simple TCP/IP Services
- Windows Internet Name Service (WINS)
ส่วนประกอบ Other Network File and Print Services มี- File Servcies for Macintosh
- Print Services for Macintosh
- Print Services for UNIX
ส่วนประกอบ Certificate Servcies มี- Certificate Services CA
- Certificate Services Web Enrollment Support
ถ้าเราประกาศเครื่องเป็น Active Directory จะมีส่วนประกอบที่ติดตั้งคือ DNS ถ้าไม่มี DNS ก็จะติดตั้ง DNS Server ให้และมี Global Catalog ด้วย
เราสามารถที่ติดตั้งบริการ โปรโตคอล หรือลูกข่ายต่างๆใน Windows server 2003 เพิ่มได้ ซึ่งบางอย่างเป็นส่วนประกอบ บางอย่างเป็น Roles หรือบทบาทในเครื่องแม่ข่าย เช่น DNS, WINS, DHCP เป็นต้นการเพิ่มส่วนประกอบโดยดีฟอลท์ Windows Server 2003 จะมีหมายเลข IP และเป็น Workgroup มี NetBIOS ทำงานบน TCP/IP โดยบรอดคลาสให้เครื่องต่างๆติดต่อเข้ามาทั้งใช้แชร์ ความปลอดภัย การขอดูเครื่อง และการพิมพ์ ส่วนประกอบที่มีคือ Client for Microsoft Network กับ File and Printer Sharing for Microsoft Netw, TCP/IPเราสามารถที่ผูกกับ Clients, Services, Protocols อื่นๆได้โดยการคลิกปุ่ม Installการติดตั้ง Client Service for Netware ต้องมีการติดตั้ง NWLink (IPX) Protocol ก่อนเมื่อติดตั้งต้องมีการกำหนด Frame Types และ Network node ถ้าเลือก Autodetect จะได้เพียงหนึ่งเพิ่ม ถ้าต้องการมากกว่าหนึ่งให้กำหนด้วย Manual
ส่วนประกอบเครือข่ายอื่นๆเราสามารถติดตั้งได้โดยปที่ Add or Remove Programs ใน Control Panel > Add/Remove Windows Components > เลือกส่วนประกอบที่ต้องการซึ่งมี Management and Monitoring Tools, Network Services, Orther Network File and Print Services, และ Certificate Servicesภายในแต่ละส่วนประกอบหลักจะประกอบด้วยManagement and Monitoring Tools มี- Connection manager administration kit
- Connection Point Services
- Network Monitor tools
- Simple Network Management Protocol
- WMI SNMP Provider
ส่วนประกอบ Networking Services มี- Domain Name System (DNS)
- Dynamic Host Configuration Protocol (DHCP)
- Internet authentication services
- RPC over HTTP Proxy
- Simple TCP/IP Services
- Windows Internet Name Service (WINS)
ส่วนประกอบ Other Network File and Print Services มี- File Servcies for Macintosh
- Print Services for Macintosh
- Print Services for UNIX
ส่วนประกอบ Certificate Servcies มี- Certificate Services CA
- Certificate Services Web Enrollment Support
ถ้าเราประกาศเครื่องเป็น Active Directory จะมีส่วนประกอบที่ติดตั้งคือ DNS ถ้าไม่มี DNS ก็จะติดตั้ง DNS Server ให้และมี Global Catalog ด้วย
เครือข่ายกับส่วนประกอบดีฟอลท์ใน Windows Server 2003
1.2 เครือข่ายกับส่วนประกอบดีฟอลท์ใน Windows Server 2003
การดู Network Connectionsเราสามารถที่ให้ระบบปฏิบัติการตรวจสอบส่วนประกอบเครือข่ายได้ด้วย เครื่องมือ Network connections ที่อยู่ใน Control Panelโดยดีฟอลท์ค่าที่กำหนดการเชื่อมต่อจะไม่อนุญาตเครือข่ายทำการสื่อสาร และมีการติดตั้งส่วนประกอบ Network clients, Services, และ Protocol ที่เกี่ยวข้อง เช่น Network Load Balancing จะติดตั้งแต่ไม่ได้เช็กบ็อกซ์ให้ทำงาน หรือ QoS Packet Scheduler ไม่ได้ติดตั้ง และ Client Service for Netware การดูค่ากำหนดในขั้นสูงเราสามารถที่ไปที่ใน Network Connections และไปเลือกเมนู Advanced กำหนดค่า Advanced Settingsในที่นี้เราสามารถที่กำหนด- การผูก ระหว่าง Protocol กับ Services ทั้ง Client และ Server- การกำหนดลำดับ การทำงานเช่น Network Provider หรือ Printer Providerค่ากำหนดดีฟอลท์สำหรับ TCP/IPเราเข้าไปดูค่าคุณสมบัิติของ TCP/IP โดยไปที่ Internet Protocol (TCP/IP) Properties ซึ่งค่าที่กำหนดจะเป็น Obtain an IP address ซึ่งการได้หมายเลข IP จะได้จาก DHCP Server ถ้าไม่มีก็จะกำหนดหมายเลข Automatic Private IP Addressing (APIPA)APIPA
เป็นฟีเจอร์ที่กำหนดเพื่อให้เครื่องในเครือข่ายเดียวกันได้หมายเลข IP ติดต่อถึงกันโดยไม่จำเป็นต้องมี DHCP Server ค่าที่ได้คืือ 169.254.0.1-169.254.25.254ตรวจสอบได้ด้วยคำสั่ง IPconfig /all ใน Command Prompt ค่า APIPA นี้เป็นค่าที่ตกลงกันในเครือข่าย Internet โดย IANA ซึ่งเมื่อได้รับหมายเลขแล้วค่า Defautl Gateway, DNS, WINS จะไม่กำหนดให้ด้วยการไม่อนุญาตให้ใช้ APIPA เราสามารถไปที่แท็บ Alterante Configuration เพื่อกำหนดแก้ไขได้ ถ้าต้องการไม่อนุญาตให้ไปที่ RegistryIPAutoconfigurationEnabled กำหนดเป็น 0 ในชนิดข้อมูล DWORD ตำแหน่ง HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\interface และรีสตาร์ทเครื่องถ้ากำหนด Disable หลายการ์ดให้ไปแค่ HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parametersการแก้ปัญหา APIPA - เครื่องที่รองรับความสามารถนี้คือระบบปฏิบัติการตั้งแต่ Windows 98 ขึ้นไป- ตรวจสอบโดยคำสั่ง IPconfig /all- ต้องการค่าหมายเลขใช้ IPconfig /renew เป็นการส่งคำร้องขอเพื่อต่ออาุยุ หรือขอหมายเลข IP จาก DHCP ถ้าไม่มี DHCP Server ก็จะได้หมายเลขในช่วง APIPA- ถ้าไม่ได้แม้กระทั่งใช้ Ipconfig /renew ให้ใช้ ipconfig /release และ /renew ใหม่ถ้ายังไม่ได้ให้ตรวจสอบฮาร์ดแวร์ที่กำหนด- เราสามารถกำหนดหมายเลข IP ได้โดยไม่จำเป็นที่ใช้ APIPA ด้วยแท็บ Alternate Configuration
ค่าดีฟอลท์เครือข่าย และ Workgroupโดยปกติ Windows Server 2003 จะกำหนดชื่อ Workgroup ว่า "Workgroup" เพื่อใช้งานใน NetBIOS ถ้าทำงานบน TCP/IP เรียกว่า NetBT (NetBIOS over TCP/IP) ซึ่งหลักการที่กำหนดเป็น Workgroup นี้ไม่มีเครื่องที่เป็นส่วนกลาง ทุกเครื่อสามารถที่ติดต่อถึงกันและกันได้ โดยรองรับ CIFS protocol ทำงานบน DNSโครงสร้างพื้นฐานเครือข่าย Windows Server 2003 และการ RoutingWindows Server 2003 เมื่อติดตั้งจะยังไม่สามารถที่ Routing ได้ต้องติดตั้ง Routing and Remote Access Service และทำการ Enable เพื่อใช้งานเครื่องที่ติดตั้งหลาย Network Card เรียกว่า Multihomed
1.2.1 สาธิตการดู Network Connections
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_01_Networkconnection.avi
1.2.2 สาธิต APIPA
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_02_APIPA.avi
1.2.3 สาธิต IPconfig
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_03_Ipconfig.avi
การดู Network Connectionsเราสามารถที่ให้ระบบปฏิบัติการตรวจสอบส่วนประกอบเครือข่ายได้ด้วย เครื่องมือ Network connections ที่อยู่ใน Control Panelโดยดีฟอลท์ค่าที่กำหนดการเชื่อมต่อจะไม่อนุญาตเครือข่ายทำการสื่อสาร และมีการติดตั้งส่วนประกอบ Network clients, Services, และ Protocol ที่เกี่ยวข้อง เช่น Network Load Balancing จะติดตั้งแต่ไม่ได้เช็กบ็อกซ์ให้ทำงาน หรือ QoS Packet Scheduler ไม่ได้ติดตั้ง และ Client Service for Netware การดูค่ากำหนดในขั้นสูงเราสามารถที่ไปที่ใน Network Connections และไปเลือกเมนู Advanced กำหนดค่า Advanced Settingsในที่นี้เราสามารถที่กำหนด- การผูก ระหว่าง Protocol กับ Services ทั้ง Client และ Server- การกำหนดลำดับ การทำงานเช่น Network Provider หรือ Printer Providerค่ากำหนดดีฟอลท์สำหรับ TCP/IPเราเข้าไปดูค่าคุณสมบัิติของ TCP/IP โดยไปที่ Internet Protocol (TCP/IP) Properties ซึ่งค่าที่กำหนดจะเป็น Obtain an IP address ซึ่งการได้หมายเลข IP จะได้จาก DHCP Server ถ้าไม่มีก็จะกำหนดหมายเลข Automatic Private IP Addressing (APIPA)APIPA
เป็นฟีเจอร์ที่กำหนดเพื่อให้เครื่องในเครือข่ายเดียวกันได้หมายเลข IP ติดต่อถึงกันโดยไม่จำเป็นต้องมี DHCP Server ค่าที่ได้คืือ 169.254.0.1-169.254.25.254ตรวจสอบได้ด้วยคำสั่ง IPconfig /all ใน Command Prompt ค่า APIPA นี้เป็นค่าที่ตกลงกันในเครือข่าย Internet โดย IANA ซึ่งเมื่อได้รับหมายเลขแล้วค่า Defautl Gateway, DNS, WINS จะไม่กำหนดให้ด้วยการไม่อนุญาตให้ใช้ APIPA เราสามารถไปที่แท็บ Alterante Configuration เพื่อกำหนดแก้ไขได้ ถ้าต้องการไม่อนุญาตให้ไปที่ RegistryIPAutoconfigurationEnabled กำหนดเป็น 0 ในชนิดข้อมูล DWORD ตำแหน่ง HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\interface และรีสตาร์ทเครื่องถ้ากำหนด Disable หลายการ์ดให้ไปแค่ HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parametersการแก้ปัญหา APIPA - เครื่องที่รองรับความสามารถนี้คือระบบปฏิบัติการตั้งแต่ Windows 98 ขึ้นไป- ตรวจสอบโดยคำสั่ง IPconfig /all- ต้องการค่าหมายเลขใช้ IPconfig /renew เป็นการส่งคำร้องขอเพื่อต่ออาุยุ หรือขอหมายเลข IP จาก DHCP ถ้าไม่มี DHCP Server ก็จะได้หมายเลขในช่วง APIPA- ถ้าไม่ได้แม้กระทั่งใช้ Ipconfig /renew ให้ใช้ ipconfig /release และ /renew ใหม่ถ้ายังไม่ได้ให้ตรวจสอบฮาร์ดแวร์ที่กำหนด- เราสามารถกำหนดหมายเลข IP ได้โดยไม่จำเป็นที่ใช้ APIPA ด้วยแท็บ Alternate Configuration
ค่าดีฟอลท์เครือข่าย และ Workgroupโดยปกติ Windows Server 2003 จะกำหนดชื่อ Workgroup ว่า "Workgroup" เพื่อใช้งานใน NetBIOS ถ้าทำงานบน TCP/IP เรียกว่า NetBT (NetBIOS over TCP/IP) ซึ่งหลักการที่กำหนดเป็น Workgroup นี้ไม่มีเครื่องที่เป็นส่วนกลาง ทุกเครื่อสามารถที่ติดต่อถึงกันและกันได้ โดยรองรับ CIFS protocol ทำงานบน DNSโครงสร้างพื้นฐานเครือข่าย Windows Server 2003 และการ RoutingWindows Server 2003 เมื่อติดตั้งจะยังไม่สามารถที่ Routing ได้ต้องติดตั้ง Routing and Remote Access Service และทำการ Enable เพื่อใช้งานเครื่องที่ติดตั้งหลาย Network Card เรียกว่า Multihomed
1.2.1 สาธิตการดู Network Connections
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_01_Networkconnection.avi
1.2.2 สาธิต APIPA
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_02_APIPA.avi
1.2.3 สาธิต IPconfig
ดูหัวข้อ หรือเอกสารที่เกี่ยวข้อง
D01_03_Ipconfig.avi
เข้าใจเกี่ยวกับโครงสร้างเครือข่ายพื้นฐาน
1.1 เข้าใจเกี่ยวกับโครงสร้างเครือข่ายพื้นฐาน
เครือข่ายคอมพิวเตอร์อาจจะมีส่วนประกอบหลากหลายเทคโนโลยี่ หลากหลายระบบ ซึ่งผู้บริหารระบบต้องมีความเข้าใจอย่างชำนิชำนานเพื่อที่บำรุงรักษา สนับสนุน และแก้ปัญหาในการทำงานต่างๆของเครือข่าย
การกำหนดโครงสร้างเครือข่ายเราต้องคำนึงถึงโครงสร้างสองแบบด้วยกันคือ Physical (กายภาพ) กับ Logical (ตามสมควร)โครงสร้างด้านกายภาพสิ่งที่ออกแบบเป็น Topology (โทโปโลยี่) ซึ่งจะคำนึงถึงฮาร์ดแวร์ เช่นสาย อุปกรณ์เครือข่าย เครื่องคอมพิวเตอร์ที่เป็นแม่ข่าย หรือลูกข่ายเป็นต้นโครงสร้างตามเหตุผล เป็นโครงสร้างออกแบบให้เป็นไปตามกายภาพ ซึ่งเน้นการสื่อสารระหว่างเครื่อง หรืออุปกรณ์ เช่น DNS, TCP/IP, Client Services ต่างๆ ในการติดต่ออาจจะมีเครือข่ายขนาดเล็ก กลาง ใหญ่ และมีระบบอื่นๆเข้ามาสนับสนุนเช่นการติดต่อทางโทรศัพท์ หรืออินเตอร์เน็ต
การวิเคราะห์เครือข่าย Windows Server 2003สิ่งที่ต้องพิจารณามีการเชื่อมต่อเครือข่าย หรือ Network Connectionsซึ่งจะมี Protocol (ซอฟต์แวร์) และ Network adapter (ฮาร์ดแวร์) หรือโมเด็ม โดยทั่วไปเมื่อติดตั้งแล้วก็จะมีส่วนประกอบอื่นๆติดตั้งตามมาด้วยเช่น Client software, Services และค่าที่กำหนดเป็น Normalโปรโตคอลเครือข่าย หรือ Network Protocolsเสมือนภาษาที่ใช้ให้เครื่องคอมพิวเตอร์พูดคุยติดต่อกัน โดยค่าที่กำหนดให้คือ TCP/IP (เวอร์ชั่น 4) ซึ่งจะใช้ติดต่อได้หลายระบบปฏิบัติการ แต่ถ้าต้องการติดตั้งเพิ่ฒก็จะมี IPX/SPX, NetBEUI, AppleTalk เป็นต้นบริการเครือข่ายหรือ Network Servicesเป็นบริการที่ติดตั้งเพื่อให้ Windows Server 2003 รองรับกับการเชื่อมต่อเครือข่ายตามบริการที่ต้องการลูกข่ายที่ใช้ หรือ Network Clientsเป็นการที่กำหนดโปรแกรมเพื่ออนุญาตให้ติดต่อกับเครื่องอื่นๆ่ เช่น Microsoft Network, Netware Network เป็นต้นหมายเลขที่อยู่ หรือ Addressingเป็นค่าที่ใช้กำหนดตำแหน่งของเครื่อง โดยที่เครื่องต้องมีที่อยู่ที่ไม่ซ้ำกัน ในโปรโตคอล TCP/IP จะมีการกำหนด IP Address และ Subnet mask ที่ใช้แยก NetworkID กับ HostID์การแก้ปัญหาชื่อ หรือ Name Resolutionการติดต่อด้วยชื่อจะทำให้ผู้ใช้นั้นง่ายต่อความเข้าใจ และการจำ ซึ่งบริการที่รองรับก็เช่น NetBIOS, DNS เป็นต้น กลุ่มเครื่องในเครือข่าย หรือ Network Computer กำหนดกลุ่มเพื่อใช้ในการติดต่อ แบ่งเป็น- Workgroup เป็นกลุ่มที่ช่วยให้เรียกใช้ทรัพยากร รองรับชื่อ NetBIOS และใช้โปรโตคอลต่างๆเข้าช่วยเช่น Common Internt File System (CiFS) และ Server Message Block (SMB) เพื่อแชร์ทรัพยากร และการเข้าดูชื่อเครื่อง- Domain เป็นการเก็บชื่อเครื่อง บริหารงานโดย Network Administrator ที่มีโครงสร้างรายชื่อ และการกำหนด Security policies มีประเภทของเรคคอร์ดที่แตกต่างกันตามหน้าที่Active Directory
เป็นระบบบัญชีรายชื่อแบบใหม่ โดยเป็นฐานข้อมูลที่ถูกกระจาย และเรพพลิเคตระหว่าง Domain Controller ซึ่งภายในประกอบด้วยออปเจคต่างๆเช่น User, Group, Computer, OUs และอื่นๆเป็นต้นใช้ระบบโครงสร้าง DNS เป็นโครงสร้างจัดลำดับชั้น และกำหนดการบริหารงานตาม Active Directory namespace และ DNS Namespace Remote Access
เป้นการกำหนดเชื่อมต่อเข้าสู่เครือข่าย Windows โดยไม่ใช่เครื่องที่อยู่ในท้องถิ่น มีสองวิธีคือการติดต่อหมุนโทรศัพท์โดยตรง หรือการติดต่อเครือข่ายที่มีอยู่กับ Virtual Private Networks (VPN) ซึ่งใน VPN นี้ผู้กำหนดต้องมีการรับรองการเข้าใช้ การอนุญาต และการเข้ารหัสNetwork Address Translation (NAT)
เป้นการแปลงหมายเลขที่อยู่จากเครือข่ายภายในให้ติดต่อภายนอก โดยอาศัยเครื่องตัวกลางเป็นผู้จัดการ (รู้จักกับเครือข่ายทั้งสอง) เช่น Internet Connection Sharing หรือ NAT Services เป็นต้องCertificate Infrastructure
เป็นโครงสร้างของการรับรอง Public key cryptography ซึ่งเป็นสิ่งที่ทำให้เครือข่าย Windows Server 2003 มีความปลอดภัย และเป็นกลไกที่ทำให้เกิดความปลอดภัยต่างๆเช่น SSL, IPSec, Smart Card และ EFS
เครือข่ายคอมพิวเตอร์อาจจะมีส่วนประกอบหลากหลายเทคโนโลยี่ หลากหลายระบบ ซึ่งผู้บริหารระบบต้องมีความเข้าใจอย่างชำนิชำนานเพื่อที่บำรุงรักษา สนับสนุน และแก้ปัญหาในการทำงานต่างๆของเครือข่าย
การกำหนดโครงสร้างเครือข่ายเราต้องคำนึงถึงโครงสร้างสองแบบด้วยกันคือ Physical (กายภาพ) กับ Logical (ตามสมควร)โครงสร้างด้านกายภาพสิ่งที่ออกแบบเป็น Topology (โทโปโลยี่) ซึ่งจะคำนึงถึงฮาร์ดแวร์ เช่นสาย อุปกรณ์เครือข่าย เครื่องคอมพิวเตอร์ที่เป็นแม่ข่าย หรือลูกข่ายเป็นต้นโครงสร้างตามเหตุผล เป็นโครงสร้างออกแบบให้เป็นไปตามกายภาพ ซึ่งเน้นการสื่อสารระหว่างเครื่อง หรืออุปกรณ์ เช่น DNS, TCP/IP, Client Services ต่างๆ ในการติดต่ออาจจะมีเครือข่ายขนาดเล็ก กลาง ใหญ่ และมีระบบอื่นๆเข้ามาสนับสนุนเช่นการติดต่อทางโทรศัพท์ หรืออินเตอร์เน็ต
การวิเคราะห์เครือข่าย Windows Server 2003สิ่งที่ต้องพิจารณามีการเชื่อมต่อเครือข่าย หรือ Network Connectionsซึ่งจะมี Protocol (ซอฟต์แวร์) และ Network adapter (ฮาร์ดแวร์) หรือโมเด็ม โดยทั่วไปเมื่อติดตั้งแล้วก็จะมีส่วนประกอบอื่นๆติดตั้งตามมาด้วยเช่น Client software, Services และค่าที่กำหนดเป็น Normalโปรโตคอลเครือข่าย หรือ Network Protocolsเสมือนภาษาที่ใช้ให้เครื่องคอมพิวเตอร์พูดคุยติดต่อกัน โดยค่าที่กำหนดให้คือ TCP/IP (เวอร์ชั่น 4) ซึ่งจะใช้ติดต่อได้หลายระบบปฏิบัติการ แต่ถ้าต้องการติดตั้งเพิ่ฒก็จะมี IPX/SPX, NetBEUI, AppleTalk เป็นต้นบริการเครือข่ายหรือ Network Servicesเป็นบริการที่ติดตั้งเพื่อให้ Windows Server 2003 รองรับกับการเชื่อมต่อเครือข่ายตามบริการที่ต้องการลูกข่ายที่ใช้ หรือ Network Clientsเป็นการที่กำหนดโปรแกรมเพื่ออนุญาตให้ติดต่อกับเครื่องอื่นๆ่ เช่น Microsoft Network, Netware Network เป็นต้นหมายเลขที่อยู่ หรือ Addressingเป็นค่าที่ใช้กำหนดตำแหน่งของเครื่อง โดยที่เครื่องต้องมีที่อยู่ที่ไม่ซ้ำกัน ในโปรโตคอล TCP/IP จะมีการกำหนด IP Address และ Subnet mask ที่ใช้แยก NetworkID กับ HostID์การแก้ปัญหาชื่อ หรือ Name Resolutionการติดต่อด้วยชื่อจะทำให้ผู้ใช้นั้นง่ายต่อความเข้าใจ และการจำ ซึ่งบริการที่รองรับก็เช่น NetBIOS, DNS เป็นต้น กลุ่มเครื่องในเครือข่าย หรือ Network Computer กำหนดกลุ่มเพื่อใช้ในการติดต่อ แบ่งเป็น- Workgroup เป็นกลุ่มที่ช่วยให้เรียกใช้ทรัพยากร รองรับชื่อ NetBIOS และใช้โปรโตคอลต่างๆเข้าช่วยเช่น Common Internt File System (CiFS) และ Server Message Block (SMB) เพื่อแชร์ทรัพยากร และการเข้าดูชื่อเครื่อง- Domain เป็นการเก็บชื่อเครื่อง บริหารงานโดย Network Administrator ที่มีโครงสร้างรายชื่อ และการกำหนด Security policies มีประเภทของเรคคอร์ดที่แตกต่างกันตามหน้าที่Active Directory
เป็นระบบบัญชีรายชื่อแบบใหม่ โดยเป็นฐานข้อมูลที่ถูกกระจาย และเรพพลิเคตระหว่าง Domain Controller ซึ่งภายในประกอบด้วยออปเจคต่างๆเช่น User, Group, Computer, OUs และอื่นๆเป็นต้นใช้ระบบโครงสร้าง DNS เป็นโครงสร้างจัดลำดับชั้น และกำหนดการบริหารงานตาม Active Directory namespace และ DNS Namespace Remote Access
เป้นการกำหนดเชื่อมต่อเข้าสู่เครือข่าย Windows โดยไม่ใช่เครื่องที่อยู่ในท้องถิ่น มีสองวิธีคือการติดต่อหมุนโทรศัพท์โดยตรง หรือการติดต่อเครือข่ายที่มีอยู่กับ Virtual Private Networks (VPN) ซึ่งใน VPN นี้ผู้กำหนดต้องมีการรับรองการเข้าใช้ การอนุญาต และการเข้ารหัสNetwork Address Translation (NAT)
เป้นการแปลงหมายเลขที่อยู่จากเครือข่ายภายในให้ติดต่อภายนอก โดยอาศัยเครื่องตัวกลางเป็นผู้จัดการ (รู้จักกับเครือข่ายทั้งสอง) เช่น Internet Connection Sharing หรือ NAT Services เป็นต้องCertificate Infrastructure
เป็นโครงสร้างของการรับรอง Public key cryptography ซึ่งเป็นสิ่งที่ทำให้เครือข่าย Windows Server 2003 มีความปลอดภัย และเป็นกลไกที่ทำให้เกิดความปลอดภัยต่างๆเช่น SSL, IPSec, Smart Card และ EFS
Error code ของ Canon
Error code ของ Canon
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink (กดปุ่ม Resume ค้าง 5 วินาทีก็สามารถพิมพ์ต่อได้)
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
(E5 นี่อาการหนัก ถ้าเช็ดทำความสะอาดหน้าสัมผัสแล้วไม่หายก็ต้องซื้อตลับใหม่)
E7 (สำหรับรุ่น iP1880) ตลับเสีย
E8 Waste ink absorber full, or platen waste ink absorber full
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
(E14 นี่ก็อาการหนัก ต้องเข้า service mode ถึงจะพิมพ์ได้)
E15 Ink cartridge is not installed
E16 - Ink remaining is unknown ..(iP1800 ให้กด resume ค้าง 5 วินาที)
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
Clear Buffer
==========
Clear Buffer Printer Canon PIXMA IP Series IP3000 IP3300 IP3500
ถ้าขึ้นไฟกระพริบ 16 ครั้ง(หมึกสีหมด) กระพริบ 4 ครั้ง (หมึกดำหมด) ให้กด Resume ค้าง 5 วินาที
Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset
Printer Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them
unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Canon inkjet printer PIXMA iP1000 iP1800
Waste Ink Counter Reset
Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
พอเข้า Service mode ได้สำเร็จ ก็เปิดโปรแกรม iPtool กดปุ่ม clear counter
Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, the indicator
(L.E.D.) should be green
6. Release both buttons
Clear Buffer Canon Inkjet Printer "S" Series Canon BJC-210 BJC-240 BJC
Canon BJC 1000 inkjet Printer Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Canon BJC-2000 BJC-2100 inkjet Printer Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
4: Hold down the RESUME/RESET button and plug in the AC power cord
5: Release RESUME/RESET after plugging in the AC Power cord.
6: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Press and HOLD RESUME/RESET for two seconds or more and release it.
9: Unplug AC Power Cord to set data.
Canon Inkjet Printer Series
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1.Unplug Power Cord
2.Hold POWER and RESUME buttons
3.Plug in Power Cord
4.Release buttons
5 front door of printer
6.Hold the CARTRIDGE and RESUME buttons
7.Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME
Canon inkjet Printer BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN,
press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Canon inkjet Printer BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
4: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be
GREEN.
5: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Canon Inkjet Printer series.
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data
Inkjet Printer
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Inkjet Printer
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
Inkjet Printer
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer
Inkjet Printer
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart
Reset ink Counter Canon Mp150/160 Printers
======================================
Befor Clear buffer Printers Canon inkjets printers
Enter Service Mode
Enter service Mode See code for reset belows
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection
Canon PIXMA iP4200 4300 6700 printer
=============================
Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or Alarm LED Lit in Orange)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on the LCD.
Cycles of blinking in orange (Alarm LED) and green(Power LED):
2 times Carriage error [5100] An error occurred in the carriage encoder signal.
Replacement
- Carriage unit (QM2-2298)
- Timing slit strip film (QC1-6394)
- Logic board ass'y (QM2-2745)*1
- Carriage motor (QK1-1500)
3 times Line feed error [6000] An error occurred in the line feed signal.
Replacement
- Timing sensor unit (QM2-2683)
- Timing slit disk film(QC1-6229)
- Feed roller ass'y (QL2-0925)
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1
- Paper feed motor (QK1-1502)
Cycles of blinking in orange (Alarm LED) and green(Power LED):
4 times Purge cam sensor error [5C00] An error occurred in the purge unit.
Replacement
- Purge unit (QM2-2299)
- Logic board ass'y (QM2-2745)*1
5 times ASF (cam) sensor error [5700]
This error takes place when feeding paper
from the ASF after an error occurred in the
ASF cam sensor.
Replacement
- Sheet feed unit (QM2-2312)
6 times Internal temperature error[5400]
The internal temperature is not proper.
Replacement
- Logic board ass'y (QM2-2745)*1
7 times Waste ink absorber full [5B00]
The waste ink absorber is full.
Replacement
- Ink absorber kit (QY5-0147)
8 times Print head temperature rise error [5200]
The print head temperature exceeded the specified value.
Replacement
- Print head (QY6-0063)
- Logic board ass'y (QM2-2745)*1
9 times EEPROM error [6800] A problem occurred in writing to the EEPROM.
Replacement
- Logic board ass'y (QM2-2745)*1
11 times Carriage lift mechanism error [5110]
The carriage did not move up or down properly.
Replacement
- PR lift shaft ass'y (QL2-0936)
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
- Carriage lift sensor unit (QM2-2678)
12 times AP position error [6A00] An error occurred in the AP motor during purging operation.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)
13 times Paper feed position error [6B00]
An error occurred in the paper feed motor.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
14 times Paper feed cam sensor error [6B10]
An error occurred in the paper feed cam sensor
during paper feeding from the front paper feed cassette.
This error is also indicated when the waste ink counter is 60% or more, and a paper jam occurs.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
15 times USB Host VBUS overcurrent [9000]
The USB Host VBUS is overloaded.
Replacement
- Logic board ass'y (QM2-2745)*1
16 times Valve sensor error [6C00] An error occurred in the valve sensor during cleaning.
Replacement
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)
17 times Motor driver error [6D00] The AD conversion value indicating the motor
driver temperature is not proper.
Replacement
- Logic board ass'y (QM2-2745)*1
19 times Ink tank position sensor error [6502]
None of the ink tank position is detected.
Replacement
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1
20 times Other hardware error [6500] The PCI bus error is detected by the ASIC.
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink (กดปุ่ม Resume ค้าง 5 วินาทีก็สามารถพิมพ์ต่อได้)
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
(E5 นี่อาการหนัก ถ้าเช็ดทำความสะอาดหน้าสัมผัสแล้วไม่หายก็ต้องซื้อตลับใหม่)
E7 (สำหรับรุ่น iP1880) ตลับเสีย
E8 Waste ink absorber full, or platen waste ink absorber full
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
(E14 นี่ก็อาการหนัก ต้องเข้า service mode ถึงจะพิมพ์ได้)
E15 Ink cartridge is not installed
E16 - Ink remaining is unknown ..(iP1800 ให้กด resume ค้าง 5 วินาที)
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
Clear Buffer
==========
Clear Buffer Printer Canon PIXMA IP Series IP3000 IP3300 IP3500
ถ้าขึ้นไฟกระพริบ 16 ครั้ง(หมึกสีหมด) กระพริบ 4 ครั้ง (หมึกดำหมด) ให้กด Resume ค้าง 5 วินาที
Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Canon inkjet printer PIXMA iP1000
Waste Ink Counter Reset
Printer Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them
unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Canon inkjet printer PIXMA iP1000 iP1800
Waste Ink Counter Reset
Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
พอเข้า Service mode ได้สำเร็จ ก็เปิดโปรแกรม iPtool กดปุ่ม clear counter
Canon inkjet Printer PIXMA iP1500
Waste Ink Counter Reset.
Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.)
should be orange.
5. Press and release the RESUME button again, the indicator
(L.E.D.) should be green
6. Release both buttons
Clear Buffer Canon Inkjet Printer "S" Series Canon BJC-210 BJC-240 BJC
Canon BJC 1000 inkjet Printer Serie
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
Canon BJC-2000 BJC-2100 inkjet Printer Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
4: Hold down the RESUME/RESET button and plug in the AC power cord
5: Release RESUME/RESET after plugging in the AC Power cord.
6: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Press and HOLD RESUME/RESET for two seconds or more and release it.
9: Unplug AC Power Cord to set data.
Canon Inkjet Printer Series
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1.Unplug Power Cord
2.Hold POWER and RESUME buttons
3.Plug in Power Cord
4.Release buttons
5 front door of printer
6.Hold the CARTRIDGE and RESUME buttons
7.Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME
Canon inkjet Printer BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN,
press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
4:Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Canon inkjet Printer BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
4: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be
GREEN.
5: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking ,
Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times.
The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Canon Inkjet Printer series.
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data
Inkjet Printer
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Inkjet Printer
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
Inkjet Printer
Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer
Inkjet Printer
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart
Reset ink Counter Canon Mp150/160 Printers
======================================
Befor Clear buffer Printers Canon inkjets printers
Enter Service Mode
Enter service Mode See code for reset belows
The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection
Canon PIXMA iP4200 4300 6700 printer
=============================
Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or Alarm LED Lit in Orange)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on the LCD.
Cycles of blinking in orange (Alarm LED) and green(Power LED):
2 times Carriage error [5100] An error occurred in the carriage encoder signal.
Replacement
- Carriage unit (QM2-2298)
- Timing slit strip film (QC1-6394)
- Logic board ass'y (QM2-2745)*1
- Carriage motor (QK1-1500)
3 times Line feed error [6000] An error occurred in the line feed signal.
Replacement
- Timing sensor unit (QM2-2683)
- Timing slit disk film(QC1-6229)
- Feed roller ass'y (QL2-0925)
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1
- Paper feed motor (QK1-1502)
Cycles of blinking in orange (Alarm LED) and green(Power LED):
4 times Purge cam sensor error [5C00] An error occurred in the purge unit.
Replacement
- Purge unit (QM2-2299)
- Logic board ass'y (QM2-2745)*1
5 times ASF (cam) sensor error [5700]
This error takes place when feeding paper
from the ASF after an error occurred in the
ASF cam sensor.
Replacement
- Sheet feed unit (QM2-2312)
6 times Internal temperature error[5400]
The internal temperature is not proper.
Replacement
- Logic board ass'y (QM2-2745)*1
7 times Waste ink absorber full [5B00]
The waste ink absorber is full.
Replacement
- Ink absorber kit (QY5-0147)
8 times Print head temperature rise error [5200]
The print head temperature exceeded the specified value.
Replacement
- Print head (QY6-0063)
- Logic board ass'y (QM2-2745)*1
9 times EEPROM error [6800] A problem occurred in writing to the EEPROM.
Replacement
- Logic board ass'y (QM2-2745)*1
11 times Carriage lift mechanism error [5110]
The carriage did not move up or down properly.
Replacement
- PR lift shaft ass'y (QL2-0936)
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
- Carriage lift sensor unit (QM2-2678)
12 times AP position error [6A00] An error occurred in the AP motor during purging operation.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)
13 times Paper feed position error [6B00]
An error occurred in the paper feed motor.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
14 times Paper feed cam sensor error [6B10]
An error occurred in the paper feed cam sensor
during paper feeding from the front paper feed cassette.
This error is also indicated when the waste ink counter is 60% or more, and a paper jam occurs.
Replacement
- Sheet feed unit (QM2-2312)
- Logic board ass'y (QM2-2745)*1
15 times USB Host VBUS overcurrent [9000]
The USB Host VBUS is overloaded.
Replacement
- Logic board ass'y (QM2-2745)*1
16 times Valve sensor error [6C00] An error occurred in the valve sensor during cleaning.
Replacement
- Logic board ass'y (QM2-2745)*1
- Purge unit (QM2-2208)
17 times Motor driver error [6D00] The AD conversion value indicating the motor
driver temperature is not proper.
Replacement
- Logic board ass'y (QM2-2745)*1
19 times Ink tank position sensor error [6502]
None of the ink tank position is detected.
Replacement
- Platen unit (QM2-2313)
- Logic board ass'y (QM2-2745)*1
20 times Other hardware error [6500] The PCI bus error is detected by the ASIC.
Error code canon mx328
Error code canon mx328
Error Code MX328
1. U051 = แผงวงจรของตลับหมึกไม่สัมผัสกับแผงวงจรในตัวเครื่อง
2. U053 = ถ้าเครื่องที่ติด Tank มีปัญหาเรื่องการเดินสาย
3. U0162 = ตลับหมึกสีหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนหน้าจอเป็นเลข 1
4. U0163 = ตลับหมึกดำหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนหน้าจอเป็นเลข 1
การรีเซตเครื่องใช้งาน Fax เป็น Auto กรณีหมึกหมด MX328
กด Menu → Fax Setting
กด Receive mode setting กด OK
กด User Setting → Auto Print เจอประโยค Print when out ink ใหเปลี่ยนจาก Off เป็น On
มาแจกกันอีกแล้วววว…
คราวนี้มาพร้อมกับ Error Code Canon MP145/150
E2(1000) No paper ไม่มีกระดาษในถาด
E3(1300) Paper jam กระดาษติด
E4(1600) No Ink หมึกหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนเป็นเลข 1
E5(1401) The ink cartridges are not installed or a non-supported ink cartridge is installed or the ink cartridges are not installed properly ถ้าเช็ดทำความสะอาดหน้าสัมผัสแล้วไม่หายก็ต้องซื้อตลับใหม่ ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E6 เกิดจาก คอนแทค ระหว่างตลับกับเครื่องพิมพ์สกปรก ทำให้สัญญาณไฟฟ้าเดินไม่สะดวก ใช้แอลกอล์(ควรใช้น้ำยาคอนแทคคลีนเนอร์) เช็ดทำความสะอาด หายได้ สิ่งสกปรกที่พบก็คือหมึกพิมพ์ เช็ดให้สะอาดทั้งสองด้าน คือที่ตลับหมึกและปุ่มที่ติดตั้งตลับหมึกที่เครื่องพิมพ์ ทำทั้ง 2 ตลับ
E8(1700) Waste ink absorber full, or platen waste ink absorber full กด OK
E9(2001) The connected digital camera / video camera does not support Camera Direct Printing ช่อง PicBriged ต่อกล้องไม่รองรับกับเครื่อง
E14(1684) The Ink cartridges whose destination are wrong ช่องใส่ตลับหมึกทำงานผิดพลาด ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E15(1682) Ink cartridge is not installed E16 – Ink remaining is unknown ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E16(1686) วัดระดับหมึกในตลับได้ อาการตลับหมึกหมด แก้โดยกด ปุ่ม Stop/Reset ค้างจนเป็นเลข 1
E19 Failed to scan head alignment sheet อาการ สแกนผิดพลาด เกิดจากหัวสแกน ลองเปิด-ปิดเครื่องใหม่
E22(5100) Carriage error ชุดหัวพ่นหมึกติดขัด ถ้าเป็น Tank สายยางอาจจะไปขัดกับ Body ในตัวเครื่อง ให้ปิดเครื่องแล้วแก้ไขโดยจัดสายยางใหม่ แล้วลองเปิดใช้งานดู
E23(6000) Paper feed error ชุด Feed ป้อนกระดาษติดขัด เกิดจากเฟืองในชุด Feed ไม่ลง Lock ต้องแกะมาแก้ไข
E24(5C00) Purge unit error ชุดล้างหัวพ่นเสียหาย
E25(5700) ASF(cam) sensor error
E26(5400) Internal temperature rise error – อาการหัวพิมพ์ไหม้ หรือตลับหมึกเสีย ลองกด Stop/Reset ค้างไว้หรือ ลองเปลี่ยนตลับหมึกใหม่ถ้าเป็นรุ่น IP จะเป็นอาการ ไฟเหลืองกระพริบ 6 ครั้ง เขียว 1 ครั้ง
E27(5B00/5B01) Waste ink absorber full or platen waste ink absorber full
- ปิดเครื่อง
- กดปุ่ม Stop/Reset ค้างไว้ และตามด้วยปุ่ม ON/OFF ค้างตาม
- ในขณะที่ยังกดปุ่ม ON/OFF ค้างอยู่ ให้ปล่อยมือจากปุ่ม Stop/Reset
- ยังกดปุ่ม ON/OFF ค้างอยู่ ให้กดปุ่ม Stop/Reset อีก 2 ครั้ง เสร็จแล้วปล่อยมือจากปุ่มทั้ง 2 ปุ่ม
- ไฟสีเขียวจะกระพริบสักพักแล้วจะหยุด
- เมื่อไฟกลายเป็นสีเขียวค้าง กดปุ่ม Stop/Reset 4 ครั้ง
- กดปุ่ม ON/OFF เพื่อปิดปริ๊นท์เตอร์ (บางทีอาจต้องกด 2 ครั้ง เพื่อปิด)
- เปิดปริ๊นท์เตอร์ ก็จะใช้งานได้ตามปกติ
E28(5200) Ink cartridge temperature rise error -อาการ ตลับหมึกผิดพลาด ลองเปิด-ปิดเครื่องใหม่
E29(6800) EEPROM error หน่วยความจำในเครื่องผิดพลาด
E33(6B00) Paper feed position error ชุด feed กระดาษติดขัดหรือดูที่ E23
E35(9000) USB Host VBUD overcurrent error – USB
E37(6D00) Abnormal motor driver error ชุด Step motor ทำงานผิดพลาด หรือมอเตอร์เสีย
E40(6500) Other hardware error
E42(5010) Scanner error
Error Code MX328
1. U051 = แผงวงจรของตลับหมึกไม่สัมผัสกับแผงวงจรในตัวเครื่อง
2. U053 = ถ้าเครื่องที่ติด Tank มีปัญหาเรื่องการเดินสาย
3. U0162 = ตลับหมึกสีหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนหน้าจอเป็นเลข 1
4. U0163 = ตลับหมึกดำหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนหน้าจอเป็นเลข 1
การรีเซตเครื่องใช้งาน Fax เป็น Auto กรณีหมึกหมด MX328
กด Menu → Fax Setting
กด Receive mode setting กด OK
กด User Setting → Auto Print เจอประโยค Print when out ink ใหเปลี่ยนจาก Off เป็น On
มาแจกกันอีกแล้วววว…
คราวนี้มาพร้อมกับ Error Code Canon MP145/150
E2(1000) No paper ไม่มีกระดาษในถาด
E3(1300) Paper jam กระดาษติด
E4(1600) No Ink หมึกหมด แก้ไขโดย กดปุ่ม Stop/Reset ค้างจนเป็นเลข 1
E5(1401) The ink cartridges are not installed or a non-supported ink cartridge is installed or the ink cartridges are not installed properly ถ้าเช็ดทำความสะอาดหน้าสัมผัสแล้วไม่หายก็ต้องซื้อตลับใหม่ ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E6 เกิดจาก คอนแทค ระหว่างตลับกับเครื่องพิมพ์สกปรก ทำให้สัญญาณไฟฟ้าเดินไม่สะดวก ใช้แอลกอล์(ควรใช้น้ำยาคอนแทคคลีนเนอร์) เช็ดทำความสะอาด หายได้ สิ่งสกปรกที่พบก็คือหมึกพิมพ์ เช็ดให้สะอาดทั้งสองด้าน คือที่ตลับหมึกและปุ่มที่ติดตั้งตลับหมึกที่เครื่องพิมพ์ ทำทั้ง 2 ตลับ
E8(1700) Waste ink absorber full, or platen waste ink absorber full กด OK
E9(2001) The connected digital camera / video camera does not support Camera Direct Printing ช่อง PicBriged ต่อกล้องไม่รองรับกับเครื่อง
E14(1684) The Ink cartridges whose destination are wrong ช่องใส่ตลับหมึกทำงานผิดพลาด ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E15(1682) Ink cartridge is not installed E16 – Ink remaining is unknown ตลับหมึกยังไม่ได้ใส่ หรือตลับหมึกเสีย
E16(1686) วัดระดับหมึกในตลับได้ อาการตลับหมึกหมด แก้โดยกด ปุ่ม Stop/Reset ค้างจนเป็นเลข 1
E19 Failed to scan head alignment sheet อาการ สแกนผิดพลาด เกิดจากหัวสแกน ลองเปิด-ปิดเครื่องใหม่
E22(5100) Carriage error ชุดหัวพ่นหมึกติดขัด ถ้าเป็น Tank สายยางอาจจะไปขัดกับ Body ในตัวเครื่อง ให้ปิดเครื่องแล้วแก้ไขโดยจัดสายยางใหม่ แล้วลองเปิดใช้งานดู
E23(6000) Paper feed error ชุด Feed ป้อนกระดาษติดขัด เกิดจากเฟืองในชุด Feed ไม่ลง Lock ต้องแกะมาแก้ไข
E24(5C00) Purge unit error ชุดล้างหัวพ่นเสียหาย
E25(5700) ASF(cam) sensor error
E26(5400) Internal temperature rise error – อาการหัวพิมพ์ไหม้ หรือตลับหมึกเสีย ลองกด Stop/Reset ค้างไว้หรือ ลองเปลี่ยนตลับหมึกใหม่ถ้าเป็นรุ่น IP จะเป็นอาการ ไฟเหลืองกระพริบ 6 ครั้ง เขียว 1 ครั้ง
E27(5B00/5B01) Waste ink absorber full or platen waste ink absorber full
- ปิดเครื่อง
- กดปุ่ม Stop/Reset ค้างไว้ และตามด้วยปุ่ม ON/OFF ค้างตาม
- ในขณะที่ยังกดปุ่ม ON/OFF ค้างอยู่ ให้ปล่อยมือจากปุ่ม Stop/Reset
- ยังกดปุ่ม ON/OFF ค้างอยู่ ให้กดปุ่ม Stop/Reset อีก 2 ครั้ง เสร็จแล้วปล่อยมือจากปุ่มทั้ง 2 ปุ่ม
- ไฟสีเขียวจะกระพริบสักพักแล้วจะหยุด
- เมื่อไฟกลายเป็นสีเขียวค้าง กดปุ่ม Stop/Reset 4 ครั้ง
- กดปุ่ม ON/OFF เพื่อปิดปริ๊นท์เตอร์ (บางทีอาจต้องกด 2 ครั้ง เพื่อปิด)
- เปิดปริ๊นท์เตอร์ ก็จะใช้งานได้ตามปกติ
E28(5200) Ink cartridge temperature rise error -อาการ ตลับหมึกผิดพลาด ลองเปิด-ปิดเครื่องใหม่
E29(6800) EEPROM error หน่วยความจำในเครื่องผิดพลาด
E33(6B00) Paper feed position error ชุด feed กระดาษติดขัดหรือดูที่ E23
E35(9000) USB Host VBUD overcurrent error – USB
E37(6D00) Abnormal motor driver error ชุด Step motor ทำงานผิดพลาด หรือมอเตอร์เสีย
E40(6500) Other hardware error
E42(5010) Scanner error
สมัครสมาชิก:
บทความ (Atom)